원문정보
Analysis of Characteristic of Filtration Pilot Plant for Combined Sewer Overflows Treatment
초록
영어
In this study, it was produced in a pilot plant for combined sewer overflows(CSOs) treatment, and solid treatment characteristic and backwashing characteristic were analyzed. Inflow range in 18.9~22.7 m3/hr (mean 21.2 m3/hr), linear velocity of filtration area was 18.9~22.7 m/hr (mean 21.2 m/hr), retention time was 3.7~4.4 min (mean 4.0 min). Effluent turbidity range in 31.8~41.9 NTU (mean 36.2 NTU) and removal efficiency was 29.4~58.9% (mean 42.9%). SS concentration range in 38.0~50.0 mg/L (mean 43.9 mg/L), removal efficiency was 68.8~84.2% (mean 76.7%). The head loss in the range of 6.0 kg/m2 solids loading increased more than 100.0 mm. After backwashing head loss was reduced to the initial value of the media. 100% in the total solids, after backwashing stage 1, 2, 37.4%, 24.8% of SS loading was discharged from pilot plant, respectively. Discharged SS loading from effluent was 21.9% and the range of residual SS loading in pilot plant was 16.0%. It was not possible to remove fine particles having an average particle diameter of 10.0 μm less by filtration using a filter material alone. Therefore, additional processes such as coagulation and sedimentation are needed to achieve stable treatment efficiency.
한국어
본 연구에서는 합류식 하수관거 월류수(CSOs) 처리를 위한 파일럿 플랜트를 제작하여 고형물처리 특성과 역세척 특 성을 분석하였다. 유입유량 18.9~22.7 m3/hr(평균 21.2 m3/hr) 범위에서 여과부의 선속도는 18.9~22.7 m/hr(평균 21.2 m/ hr), 체류시간은 3.7~4.4 min(평균 4.0 min)로 나타났다. 처리수의 탁도 범위는 31.8~41.9 NTU(평균 36.2 NTU)로 29.4~58.9%(평균 42.9%)의 처리효율을 나타내었다. SS는 38.0~50.0 mg/L(평균 43.9 mg/L) 농도범위로 68.8~84.2%(평균 76.7%)의 처리효율을 나타내었다. 고형물부하 6.0 kg/m2 이후 범위에서 손실수두가 100.0 mm 이상 증가하였으나, 역세 척 후에는 여재의 초기손실수두 값으로 환원되었다. 고형물을 100.0%로 하였을 때 유출되는 고형물은 21.9%였으며, 정 체수와 처리수의 역세척으로 각각 37.4%, 24.8%가 배출되었다. 여과장치 내에 남아있는 잔류고형물은 16.0%로 나타났 다. 여재를 이용한 여과만으로는 평균 입경 10.0 μm 이하의 미세입자를 제거할 수 없었다. 따라서 안정적인 처리효율 확 보를 위해서는 이를 처리하기 위한 응집 및 침전 등과 같은 추가적인 공정이 필요할 것으로 판단된다.
목차
요약문
I. 서론
II. 연구 방법
1. 실험장치
2. 여재의 특성
3. 실험방법
III. 연구결과 및 고찰
1. 고형물처리 특성
2. 역세척 특성
IV. 결론
References